ITENE achieves detergent packaging through decontamination processes of recycled polyolefins 

June 27th, 2024

ITENE

El ITENE technology center has developed advanced processes decontamination of recycled polyolefins, specifically recycled high-density polyethylene (HDPE), which has allowed it achieve detergent packaging through extrusion blowing them in different sizes. 

The research has been carried out between June 2023 and 2024 within the framework of the ReciPOL project, financed by the Valencian Institute of Business Competitiveness (IVACE+i), and has focused on obtaining high-quality recycled materials.  

The project manager at ITENE, Félix González, explained that "although the post-consumer plastic decontamination processes developed usually focus on polyethylene terephthalate (PET), the elimination of contaminants in polyolefins is more complex due to their greater internal migration and low thermal stability, which generates degradation products. “These difficulties are aggravated by recycling cycles that involve greater degradation and contact with other contaminants, which can limit their application in sectors with higher quality requirements,” the researcher stressed. 

Therefore, in this project, we have sought to obtain new decontamination technologies for recycled polyolefins to increase recycling rates and promote their use in applications with higher quality requirements. Specifically, the work has focused on the conditioning, pretreatment, decontamination and transformation of waste polyolefins that are currently destined for low-value applications. 

Analysis of contaminants and controlled contamination 

For this, an analysis of post-consumer polyolefin contaminants was carried out. This allowed us to select the most critical ones in order to see what challenges the project was facing. Furthermore, through this selection and the optimization of the controlled contamination process (challenge test) it was possible to measure the effectiveness of the pretreatment and decontamination processes that were developed in the following stages. 

Subsequently, work was done on the development of polyolefin conditioning and decontamination processes. Firstly, a pretreatment process was carried out, once optimized and synergistically aligned with subsequent decontamination processes, where three different technologies were tested: water vapor, ozone and supercritical CO2. Water vapor was selected as the technology that met both good effectiveness in removing contaminants and feasibility, both economically and technically, of scaling this process. It is true that supercritical CO2 had greater efficiency, but due to the conditions usually used of hyperbaric pressures and high temperatures that achieve this condition, water vapor technology was chosen. 

Afterwards, the evaluation of the selected technology and its pilot scaling were carried out in a water vapor decontamination equipment designed at ITENE to scale the process and serve as a prototype for its validation and bring it closer to an industrial scale.  

Likewise, they selected additives to improve processability and material properties recycled, for which different formulations were designed that allowed optimizing the decontamination of the polyolefins and the properties of the packaging. Thus, the formulations that presented the best results were validated by hollow body blown extrusion to subsequently obtain bottles. Furthermore, it was found that the fluidity of the materials obtained was adequate and that the tensile strength was similar to that of the virgin material, although they had greater rigidity. Finally, the most promising formulation was selected for industrial validation. 

You may be interested in continuing reading ...

Spain will multiply by 40 the waste treatment capacities for chemical recycling in 2025

Plastics Europe (pan-European association of plastics producers), Feique (Business Federation of the Spanish Chemical Industry) and Aimplas (Plastic Technological Institute) have presented the ...

Lanjarón presents its 50cl bottle made entirely with recycled plastic

Lanjarón, from Aguas Danone, adds another format to its offer made of 100% recycled plastic (rPET), the 50cl bottle. The brand thus takes another step in its commitment to the environment and ...

Coveris launches ReCover to keep plastics circular

In line with its No Waste vision, Coveris now presents ReCover, bringing together all efforts in waste sourcing, processing and recycling to close the circular recycling loop...

AIJU hosts the conference “Circularity Strategies and Industrial Symbiosis in the Plastic Industry”

The use of post-consumer recycled plastics increases by 70% compared to 2022, reaching 6 million tons, according to the recent report by Plastics Europe. Likewise, according to this same i...

Huhtamaki launches Push Tab®, an aluminum-free monomaterial PET blister pack

Huhtamaki presents a sustainable innovation for the global pharmaceutical and healthcare industry: the Push Tab® blister is made of monomaterial PET and does not contain aluminum. Being PET monomaterial, it continues ...

Biological and chemical processes allow the recovery of PET plastic waste that is difficult to recycle

The ITENE technology center has developed new biological and chemical processes that make it possible to recover waste from multi-layer, single-layer and colored containers made of PET plastic (polyethylene terephthalate...
Translate »